Can You Put Jack Stands on Control Arms

No, it is not recommended to put jack stands on control arms. Jack stands are usually placed underneath a vehicle’s frame and other strong points that can support the weight of the car safely. Control arms are not designed to bear the full weight of a vehicle; they are only meant to move and support suspension components like shocks and struts.

Therefore, putting jack stands on control arms would risk bending or breaking them due to excessive strain from bearing too much weight for too long. Additionally, because of their design, placing jack stands directly onto control arms could potentially damage other suspension parts as well.

  • Step 1: Park your car on a flat surface
  • Make sure the wheels are blocked and that the parking brake is engaged
  • Step 2: Raise the vehicle up with a jack until it reaches the desired height for putting on jack stands
  • Step 3: Place two jack stands, one at each side of your control arms, directly underneath them, ensuring they are centered and stable
  • Step 4: Slowly lower the vehicle onto the jack stands until it rests safely on them
  • You can use a wrench to turn down any nuts or bolts if necessary to secure them in place before you release pressure from your hydraulic floor jack
  • Step 5 : Test all four corners of your car to make sure that it is sitting evenly and securely on the jack stands before beginning work beneath it
Can You Put Jack Stands on Control Arms

Credit: mechanics.stackexchange.com

Can I Put a Jack Stand under a Control Arm?

Yes, you can put a jack stand under a control arm. This is because most control arms are made from metal, which is strong enough to support the weight of the vehicle. However, it’s important to make sure that your jack stands are in good condition and have a wide base so they don’t tip over when pressure is applied.

Depending on the model of car you own, there may be specific instructions for where exactly to place the jack stand beneath the control arm but if not then just position it so that it supports as much weight as possible without putting undue strain on any single point. When setting up your jack stand, always use safety equipment such as eye protection and gloves and remember to never exceed its rated capacity or leave a vehicle supported by only one side while working underneath it.

Where Do You Put the Jack Stand on a Control Arm?

When using a jack stand to support the control arm of a vehicle, it is important to place the jack stand in an appropriate spot. The best location for a jack stand when supporting the control arm is near where the lower ball joint connects to it. This will provide stability and make sure that no excessive pressure is put on other components while working on the car.

Make sure that you also use safety equipment such as wheel chocks or blocks to keep your vehicle from rolling while working on it with a jack stand. Be careful not to place too much weight on any single point of contact when raising and lowering your car; this can cause permanent damage and compromise its structural integrity over time if done incorrectly.

Where Should Jack Stands Be Placed?

When using jack stands, it is important to ensure that they are placed correctly and securely. Jack stands should always be positioned on a level surface at the same height as the lift point of your car or truck. Make sure that you place them far enough apart so that the vehicle won’t tip over when lifted.

Additionally, position them in such a manner that there will be no contact with any moving parts underneath the vehicle, like drive shafts and exhaust components. When placing your jack stand under an axle or frame rail, make sure to double check for obstructions like brake lines or fuel lines before lifting your vehicle up off the ground onto two jack stands. Once your vehicle is resting safely on two sturdy jack stands, go ahead and lower the hydraulic floor jack until it has been completely removed from under the car or truck.

Where Not to Put a Jack Stand?

When it comes to safely supporting a car for repairs, the most important decision is where not to put the jack stand. It is vital that you place your jack stands on hard, level ground and away from any potential pinch points. Do not place them near anything that could move or shift during repairs because this can cause serious injury if the car falls off of them.

Additionally, avoid placing jack stands under power steering components as they are too weak to withstand the additional force placed upon them while raising and lowering a vehicle with an automotive lift or scissorjack. Furthermore, never place one directly beneath the vehicle’s center of gravity – instead raise each side evenly until both have adequate support before getting underneath the car. Finally, always use quality stands rated for more weight than what your vehicle weighs and make sure they lock into position when fully extended before beginning work on your vehicle!

How To Properly Lift a Car on 4 Jack Stands

Where to Put Jack Stands

When using jack stands, it is important to make sure they are placed on a flat, level surface that can bear the weight of your vehicle. This can include an asphalt or concrete driveway, garage floor, or other sturdy foundation. You should also be mindful of where you place them in relation to the jacking points on your car; ideally, each stand should be positioned directly beneath one of these points so that your vehicle is evenly supported and won’t slip off the stands.

Conclusion

In conclusion, it is not recommended to put jack stands on control arms due to the fact that they can cause serious damage and compromise the safety of your vehicle. If you need to lift your vehicle for maintenance or repairs, be sure to use a hydraulic jack and other appropriate lifting tools instead. Jack stands should only be used when supporting a raised portion of the car from underneath, such as on frame rails or suspension components like sway bars or lower control arms.

Using these methods correctly will help ensure that your vehicle remains safe and secure during service tasks.

Scroll to Top