To turn off the maintenance light on your Toyota Tacoma, simply press and hold the odometer reset button for about 5 seconds. The light will then turn off.
- Enter the vehicle and turn the key to the “on” position without starting the engine
- Press and release the gas pedal three times within five seconds
- The maintenance light will now blink for approximately 60 seconds before turning off
Turn off Maintenance Light Toyota Camry
Assuming you would like a blog post discussing how to turn off the maintenance light on a Toyota Camry:
“How to Turn Off Maintenance Light on Toyota Camry”
Most people don’t know this, but you can actually turn off the maintenance light on your Toyota Camry.
It’s actually really easy to do and only takes a few minutes. Here’s how:
First, locate the diagnostic link connector under the hood of your car.
It should be located near the battery. Once you’ve found it, disconnect the negative terminal of your battery. This will reset all the electronic systems in your car, including the maintenance light.
Now, start up your car and see if the maintenance light is still illuminated. If it is, then simply press and hold down the Trip button (it’s usually located on your instrument cluster) for about five seconds. This should turn off the maintenance light.
And that’s it! Now you know how to turn off the maintenance light on your Toyota Camry whenever it comes on.
How Do I Reset the Maintenance Required Light on My Toyota Tacoma?
Assuming you would like a blog post discussing how to reset the maintenance required light on a Toyota Tacoma:
“How do I reset the maintenance required light on my Toyota Tacoma?”
If you need to reset the Maintenance Required Light on your Toyota Tacoma, follow these steps:
1. Start the engine and drive for about 10 minutes to allow the system to initialize.
2. Turn off the engine and wait for about five seconds.
3. Press and hold down the trip meter button while turning the ignition back on without starting the engine.
4. Keep pressing and holding until “trip A” is displayed. This will take care of any scheduled maintenance that was due. If no message is displayed, try again from step one making sure not to release the button too soon.
How Do I Reset the Maintenance Light on a 2017 Toyota Tacoma?
Assuming you would like a step-by-step guide on resetting the maintenance light on your 2017 Toyota Tacoma:
1. Locate the small black button next to the odometer display. It is likely labeled with an image of an oil can.
2. Press and hold this button for about five seconds.
3. The display should now read “reset” – press the button again to confirm.
4. The maintenance light should now be reset!
How Do You Turn off the Maintenance Light on a 2013 Toyota Tacoma?
Assuming you are talking about the maintenance required light: To turn it off, simply press and hold the odometer reset button on your instrument panel for approximately 5 seconds.
How Do You Turn off the Maintenance Required Light on a 2005 Toyota Tacoma?
Assuming you would like tips on resetting the maintenance required light on your 2005 Toyota Tacoma:
One way to reset the maintenance required light on your 2005 Toyota Tacoma is to simply disconnect the battery for about 30 seconds. This will cause the system to reboot and should clear any error codes that may have been causing the light to stay illuminated.
Another method is to use a code scanner or OBD-II reader to clear the codes from the vehicle’s computer. Once the codes have been cleared, the maintenance required light should no longer be lit.
Conclusion
If you own a Toyota Tacoma, you may have noticed the maintenance light come on occasionally. This is normal and nothing to worry about! The light is simply reminding you to perform some basic maintenance tasks on your truck.
Here’s how to turn it off:
First, open the hood and locate the oil dipstick. Pull it out and wipe it clean with a rag.
Reinsert the dipstick all the way back into its housing.
Next, locate the power steering fluid reservoir (it will have a steering wheel icon on it). Remove the cap and top off the fluid if necessary.
Replace the cap when done.
Finally, go to your gas tank and unscrew the cap. Using a funnel, add fresh engine coolant until it reaches the “full” line on the side of the tank.
Screw the cap back on tightly when finished.
Once you’ve completed these steps, simply drive your Tacoma for a few minutes and the maintenance light should turn off automatically!
