To put a jeep wrangler in neutral with a dead battery, you can locate the manual shift lever under the transfer case shifter boot and then follow some easy shifts. A jeep wrangler is an off-road vehicle that has earned its name for its ability to trek rough terrains.
Over time, your jeep wrangler’s battery may lose its charge and eventually go dead, which could leave you stranded on the roadside. In this situation, you may need to put your jeep wrangler in neutral to move it around without the engine running. In this article, we’ll discuss how to put jeep wrangler in neutral with a dead battery.
Credit: www.motortrend.com
**Locate Your Transfer Case**
To put a jeep wrangler in neutral with a dead battery, you need to locate your transfer case. The transfer case is what allows the engine’s power to be distributed to the wheels. Once you locate it, you can use the shift lever to manually put the transfer case in neutral.
First, make sure the engine is off and the parking brake is engaged. Then, remove the shift lever boot and use a wrench to turn the shift lever clockwise until it clicks into the neutral position. Once your transfer case is in neutral, you can safely move and tow your jeep without damaging the transmission.
Remember to always refer to your owner’s manual for specific instructions and precautions.
**Putting Your Jeep Wrangler In Neutral**
When your jeep wrangler battery is dead, there are a few steps to follow to put it in neutral. First, locate the transfer case shift lever. Then, remove the shift lever boot and access the shift linkage. Disconnect the shift linkage from the transfer case shift lever by removing the cotter pin and washer.
Move the linkage to the neutral position and re-install the cotter pin and washer. Finally, test the shifter for proper neutral position by trying to move the vehicle. It’s important to follow these steps carefully to ensure your safety and the safety of others.
Always refer to your owner’s manual for specific instructions and diagrams.
Jeep Starting Problem? Battery Drain? ESS (Electronic Start Stop) System / Auxiliary Battery
**Removing Your Dead Battery**
If you need to put your jeep wrangler in neutral with a dead battery, then you’ll need to first remove the battery. Before doing this, it’s important to wear gloves and safety glasses to protect yourself from any acid. Begin by using a wrench to loosen the negative cable, followed by the positive cable.
Then, remove the battery strap and lift the battery out of its compartment. With the battery removed, you can now shift your jeep wrangler into neutral by using the transmission’s shift lever. Remember to take care when handling the battery and dispose of it properly to avoid any environmental harm.
**Conclusion**
Following the above guidelines, putting a jeep wrangler in neutral with a dead battery is a simple task. Begin by locating the manual transmission shift lever on the side of the transmission. Then, remove the silver bolts and washer found on the gear shifter plate.
Once removed, use a long-handled, slim screwdriver to reach through the plate’s hole and push the shifter into neutral. It’s important to note that this technique only works in manual transmission jeeps, and attempting it in an automatic jeep can cause damage to the vehicle.
Always exercise caution and consult a professional if necessary.
Frequently Asked Questions For How To Put Jeep Wrangler In Neutral With Dead Battery
How Do I Put My Jeep Wrangler In Neutral With A Dead Battery?
To put your jeep wrangler in neutral with a dead battery, you need to locate the shift lock override slot, typically found near the shifter. Use a flathead screwdriver or another similar tool to push down on the tab inside the slot and move the shifter into neutral.
Can I Push My Jeep Wrangler If The Battery Is Dead?
Yes, you can push your jeep wrangler with a dead battery, but you need to put it in neutral first. Refer to the previous answer to find out how to put your jeep in neutral.
Will Towing My Jeep Wrangler Damage The Transmission?
If you want to tow your jeep wrangler without causing damage, you need to ensure that it’s in neutral. Towing it in any other way, such as with the wheels on the ground or with the parking brake engaged, can lead to significant transmission damage.
Conclusion
Putting a jeep wrangler in neutral with a dead battery might seem like a daunting task, but it is actually quite simple. The first step is to locate the transfer case of the jeep, which is usually situated on the right side.
Once you have found it, you can use a flathead screwdriver or a pair of pliers to move the shift lever to the desired neutral position. Although it is always recommended to keep the battery charged, this simple procedure can help you avoid towing the jeep to a garage.
It is crucial to remember to engage the transmission brake before moving the jeep in neutral. Following these simple steps will help you get your jeep out of a tough situation, and hit the road again in no time.
