If your Kymco Agility 50 is restricted, it means that the scooter has a speed limit of 30 miles per hour. To derestrict the scooter, you will need to remove the restrictor plate from the engine. The restrictor plate is located under the left side cover of the engine.
Once you have removed the restrictor plate, you will need to adjust the carburetor so that it is running leaner.
- Open the gas cap and unscrew the fuel line
- Remove the spark plug and unscrew the headlight bulb
- Unscrew the four screws holding the plastic fairing on
- Pop off the speedometer cable from its housing
- Unplug the kill switch wire from its connector
- Take out the two bolts holding in the battery tray and remove it along with the battery
How to Make Kymco Agility 50 Faster
If you own a Kymco Agility 50 and are looking for ways to make it faster, there are a few things you can do. First, make sure the engine is properly tuned. A well-tuned engine will run more efficiently and produce more power.
Next, consider installing a performance exhaust system. A good exhaust system can improve airflow and help the engine breathe better, resulting in more power. Finally, adding a big bore kit to your Kymco Agility 50 can really wake up the engine and dramatically increase its power output.
If you follow these tips, you should be able to significantly improve the performance of your Kymco Agility 50.
Credit: www.pedparts.co.uk
How Fast Will a Derestricted 50Cc Scooter Go?
Assuming you are talking about a 50cc scooter with no speed limiters or other restrictions, most 50cc scooters have a maximum speed between 35 and 40 mph. However, there are always exceptions and some models may be capable of reaching speeds up to 45 mph or even higher. Ultimately, the answer to this question will vary depending on the specific model of scooter that you have.
How is a 50Cc Moped Restricted?
A 50cc moped is typically restricted by a CDI (Capacitive Discharge Ignition) box. This limits the amount of voltage that can be sent to the spark plug, and therefore the amount of power that can be produced by the engine. The result is a vehicle with reduced speed and acceleration compared to an unrestricted moped or motorcycle.
Where is the Spark Plug on a Kymco Moped?
The spark plug on a Kymco moped is located on the side of the engine, near the exhaust. It is typically a silver or black colored cap that unscrews from the side of the engine.
How to Change the Oil in a Kymco Agility?
If you own a Kymco Agility, sooner or later you will need to change the oil. It’s not a difficult task, but there are a few things you need to know before you get started. This blog post will show you how to change the oil in your Kymco Agility, step by step.
Before you start, make sure that you have all the supplies and tools that you need. You will need:
-Engine oil (the specific type and amount recommended for your Kymco Agility can be found in the owner’s manual)
-A clean funnel
-A drain pan
-An oil filter (again, the specific type and amount recommended for your Kymco Agility can be found in the owner’s manual)
-A socket wrench set
Once you have everything gathered together, it’s time to get started. The first step is to warm up your engine for about 5 minutes.
This will help loosen the old oil and make it easier to drain out. Next, locate the drain plug on the bottom of your engine (it should be clearly marked). Place your drain pan underneath and then remove the drain plug using your socket wrench.
Allow all of the old oil to drain out completely. Once it has finished draining, replace the drain plug and snug it tight with your socket wrench.
Now it’s time to replace your old oil filter with a new one.
Locate the filter (it should also be clearly marked) and unscrew it using either an adjustable wrench or a pair of pliers. Be careful not to touch the exposed end of the old filter – used filters can be very hot! Install the new filter by screwing it on until it is hand tight only – do not over tighten as this could damage both the filter and/or housing. Wipe any spilled oil off of surfaces using a clean rag or paper towel as necessary so that everything stays clean during reassembly..
Kymco Agility 50cc boss and rollers derestriction
Conclusion
Kymco Agility 50 is a great scooter for those looking for an affordable and easy to ride option. However, many people find that the top speed of 30mph is too slow for their needs. Luckily, there are a few ways to derestrict the Kymco Agility 50 so that it can reach speeds of up to 40mph.
Doing this is relatively simple and only requires a few tools and supplies that can be easily found online or at a local hardware store. With a little bit of time and effort, you can have your Kymco Agility 50 reaching the speeds you need in no time!
