There are a few ways to check your Harley motor mounts. You can visually inspect them for cracks or damage. You can also check for excessive movement by putting your bike on the stand and moving it back and forth.
If you hear creaking or popping, that could be a sign of damage as well.
- Harley motor mounts are located on the frame of the motorcycle, just below the engine
- To check the mounts, first put the bike on a stand so that it is level and secure
- With the engine at idle, grab each mount and try to move it up and down and side to side
- If there is any movement in the mounts, they need to be tightened or replaced
Harley Front Engine Mount Stabilizer Link
If you have a Harley-Davidson motorcycle with a front engine mount, then you know how important it is to keep it stabilized. The front engine mount stabilizer link is what helps to keep the engine from moving around too much, and it also provides some vibration dampening. If your link goes bad, or if it breaks, then you’ll likely notice some increased vibration in the handlebars and footpegs.
In extreme cases, the engine may even move around enough to cause damage to the frame or other parts of the bike.
The good news is that replacing a broken or damaged stabilizer link is relatively easy and inexpensive. You can find them online or at most motorcycle parts stores.
Installation is straightforward, but make sure to follow the instructions in your service manual carefully. With a new stabilizer link in place, your Harley should ride just like it did before.
Credit: www.roadglide.org
How Do You Check Motor Mounts on a Harley?
If your Harley-Davidson is vibrating excessively, it could be a sign that your motor mounts are worn out. You should check your motor mounts every few thousand miles to ensure they are in good condition.
There are a few ways you can check your motor mounts.
One way is to put the bike on its center stand and try to push and pull on the engine. There should be very little movement. If there is a lot of movement, then your motor mounts are likely worn out.
Another way to check is to take off the primary cover and look at the rubber isolators between the frame and engine. If these are cracked or broken, then it’s time to replace the motor mounts.
Lastly, you can also listen for any rattling or knocking noises coming from the engine area when the bike is idling.
This could also be a sign that the motor mounts need to be replaced.
If you find that your motor mounts need to be replaced, it’s best to take it to a qualified mechanic who can do the job properly. Replacing motor mounts is not a difficult task, but it does require some knowledge and experience with working on motorcycles.
How Do I Know If My Motor Mounts are Worn?
If your motor mounts are worn, you may notice that your car vibrates more than usual while idling. Additionally, you may hear unusual noises coming from the engine bay, or feel like the engine is “shifting” while driving. If you suspect that your motor mounts are worn, it’s best to have a mechanic take a look.
They will be able to tell for sure if the mounts are worn and need to be replaced.
How Do I Check My Motor Mounts by Myself?
Assuming you would like tips on how to check your motor mounts by yourself:
One way to check if your car’s motor mounts are bad is to turn the engine on and put the car in drive or reverse, then see if the engine moves excessively. If there’s a lot of movement, then the motor mounts may be bad.
Another way to check is to take a look at the rubber bushings that connect the metal brackets holding the engine in place. If these are cracked or broken, then it’s likely that the motor mounts are bad.
However, it’s always best to consult with a professional mechanic to get an accurate diagnosis.
Can You Visually Inspect Motor Mounts?
Yes, you can visually inspect motor mounts. If they are cracked or broken, they will need to be replaced.
Harley Davidson Motor Mount Inspection
Conclusion
If you’re a Harley rider, you know how important it is to keep your bike in top condition. One way to do that is to check the motor mounts regularly. Here’s how:
1. Park your bike on level ground and put it in neutral.
2. With the engine off, grab each side of the front fork and push/pull on the forks. There should be no movement at all in the engine or frame.
If there is any movement, then your motor mounts need to be checked/replaced.
3. Another way to check the motor mounts is by starting the engine and putting it in gear (without moving the bike). Again, grab each side of the front fork and push/pull on the forks.
There should be NO movement whatsoever in either the engine or frame. If there is any movement, then your motor mounts need to be checked/replaced as soon as possible!
