If your Pontiac Grand Am has a keyless entry system, you can start the car without a key. All you need is the remote control for the keyless entry system.
To start the car, just press the “Start” button on the remote.
If your car does not have a keyless entry system, then you will need to use a key to start it.
- Open the driver’s side door and locate the ignition cylinder on the steering column
- Insert a small, flat-head screwdriver into the slot on the bottom of the ignition cylinder and turn it counterclockwise until it stops
- With the screwdriver still in place, insert a Pontiac Grand Am key into the ignition cylinder and turn it clockwise until it stops
- This will release the locking pin inside the cylinder
- Remove the screwdriver and key from the ignition cylinder
- Insert the Pontiac Grand Am key into the ignition switch and turn it tothe “On” position
How to Start a 2004 Pontiac Grand am Without a Key
It is possible to start a 2004 Pontiac Grand Am without a key. This can be done by using a screwdriver to bypass the ignition switch. First, remove the screws from the lower part of the steering column cover.
Next, use the screwdriver to pry off the cover. Once the cover is removed, you will see the ignition switch. Use the screwdriver to rotate the ignition switch until it is in the “run” position.
Finally, replace the steering column cover and screw it back into place.
Credit: sparkys-answers.com
How Do I Turn My Ignition Switch on Without the Key?
If your car has an automatic transmission, the ignition switch is on the left side of the steering column. The switch is usually labeled with “OFF,” “ACC,” and “ON.” To turn on your car without the key, first make sure that it’s in park.
Then, push down on the brake pedal and hold it. Next, turn the ignition switch to the “ACC” position. Finally, release the brake pedal and press down on the start button.
If your car has a manual transmission, you’ll need to put it in neutral before turning on the ignition switch.
How Do You Turn off the Theft System on a Pontiac Grand Am?
If your Pontiac Grand Am has an active theft system, you can disable it by following these steps:
1. Locate the theft system control module. This is usually located in the trunk, under the carpet near the spare tire.
2. Disconnect the control module from the vehicle’s electrical system. This can be done by disconnecting the battery or pulling the fuse for the module.
3. Wait for 30 seconds to allow the module to reset itself.
4. Reconnect the control module to the vehicle’s electrical system and test it to see if it is disabled. If it is still active, you may need to replace the module altogether.
How Do You Bypass the Security on a 2003 Pontiac Grand Am?
Assuming you are referring to the security system: The 2003 Pontiac Grand Am has a PASS-Key III+ (PK3+) theft deterrent system. This means that there is a transponder in the ignition key that sends a signal to the car’s computer.
If the correct signal is not received, the car will not start. There are a few ways to bypass this system. One is to use a “universal” transponder key.
These keys are programmed to send the correct signal for many different makes and models of cars. Another way is to use a “bypass module.” This is a device that tricks the car’s computer into thinking that the correct signal is being received, even if it’s not.
If you want to bypass the security system on your 2003 Pontiac Grand Am, your best bet is to use a universal transponder key or a bypass module.
How Do You Start an Old Car Without a Key?
Assuming you don’t have a spare key and you’re stuck with a car that won’t start, there are still a few ways to get it going. If your car has an automatic transmission, the first thing you’ll need to do is locate the starter solenoid.
This should be easy to find – it’s usually located on or near the starter motor, which is typically on the engine block near the bottom of the vehicle.
Once you’ve found it, see if there’s a loose wire attached to it. If so, reattach it and try starting the car again. If that doesn’t work, or if your car has a manual transmission, then you’ll need to jump-start the engine using another vehicle.
Make sure both cars are turned off and in park (or in gear for manual transmissions), then open their hoods and locate each other’s battery.
Attach one end of each jumper cable to the positive terminal of one battery, then attach the other end of each cable to the negative terminal of the other battery – making sure not to touch any metal surfaces with exposed wires.
Finally, start up one car and let it idle for a minute or two before trying to start your old car.
How To Start Car With No Key (For Free)
